Leds work nothing else does
@paxli wrote: Have an Envirphat which worked fine. My rPi Zero stopped working so got a new one. Just transferred SD card over and updated all software and fresh install of envirophat software. The...
View ArticleRFM69 433Mhz Bonnet receiving packets problem
@mikeathan wrote: I have a Adafruit RFM69 433 Mhz bonnet connected to a Raspberry Pi zero with a coil antenna for 433Mhz. Am running the example python code from the adafruit...
View ArticleContinuously running Python code for Pimoroni buttonshim on Raspberry Pi...
@deathsmith8 wrote: I am using a Raspberry Pi 3B+ to display a website/websites on a screen, and recently attached a Pimoroni Button-Shim. Since writing some Python code (below) I have had the buttons...
View ArticleEnviro+ install script error
@SteveHartl wrote: trying to install the new enviro+ install script fails with error ;- Searching for pms5003 Reading https://pypi.python.org/simple/pms5003/ Download error on...
View ArticleNew to Pi, help me know what parts I need
@avb wrote: Hi, I’m building a greenhouse raspberry pi device. I know how to program in python and how to handle raspberry pi through CLI. What I don’t know is what parts I should order for my...
View ArticleBreakout hat with BME680
@tstephen wrote: Hey, Just getting started with the breakout hat. Pi 3B+ was working fine, I grabbed the examples and shut it down. Added the breakout hat complete with BME680 and reinserted power....
View ArticleNo audio out using pygame and pHAT DAC
@Blinkyghost5674 wrote: I’ve been working on a bigger project on rpi 3 and wanted to move to the zero to save space. The project has mp3 files that play using pygame.mixer.music and worked on the rpi...
View ArticleICM20948 seismometer
@PiMuncher wrote: Hi, I’d like to use the example seismometer script with my ICM20948 9 DoF motion sensor but the script is setup for the 6 DoF variant. What changes do I need to make? Posts: 1...
View ArticleLipo shim with USB Power
@krischaplin wrote: Hello, Apologies if this has been answered before. I am planning on direct soldering the Lipo Shim. However, during development I would like to power my PI via USB. Can I do so...
View ArticleIs there a case for the Pi Zero and Enviro+?
@Bodestone wrote: Just putting them together now but I feel there should be an appropriate case that protects them while letting all seonsors work. Any suggestions of official cases or 3DP templates...
View ArticleClik here to view.
HyperPixel 4.0: sizzling of the screen
@bropars wrote: Hello, I have 3 hyperpixel screen with touchscreen and without and I have the same problem on all screen. After approximately 30 minutes the screen sizzle. So i has disable the...
View ArticleClik here to view.
Minim pan tilt kit
@skypickle wrote: I got this adafruit.com Mini Pan-Tilt Kit - Assembled with Micro Servos This fully-assembled pan-tilt kit is the perfect way to give your project full range motion with two micro...
View ArticlePhat dac + python
@Blinkyghost5674 wrote: Hello everyone, I’ve been trying to get audio out of a python script. Before I got the dac the program worked fine. Then I installed the dac and did the automatic config as...
View ArticleRPI Zero W, I2S, MAX98357A, Spotify, AirPlay
@Olle wrote: Hi. I have bought an RPi Zero W and an Adafruit MAX98357A (I2S amp) of yours (Pimoroni). I want to install Spotify or Airplay according to your instructions. I have tried to install...
View ArticleClik here to view.
Automation HAT Analogue In spurious reading
@hazza wrote: The analogue channel frequently (approx 10% of the time) gives incorrect readings, often 4.37, or 0.03. I’ve wired to the HAT 3.3V and 5V sources as well as a 1.5V battery. I’ve also...
View Article? issue with Humidity values on Enviro+ ( Enviro plus )
@SteveHartl wrote: Hi, has anyone else noted issues with the humidity values returned by the new Enviro+ ? I am sat in thick fog and have two other sensors running (Aeotec Multisensor 6 & DHT22)...
View ArticleQuestions about GPIO pins used on Fan Shim
@dhylands wrote: I was wondering if schematics for the Fan Shim are available? The python library references GPIO 17 & 18, but looking at the photos, there also appear to be connections to GPIO 14...
View ArticleRaspberry Pi 4 wont boot or illuminate any LEDs
@t3rminal wrote: So I received my Pi 4 yesterday and opened it today. I firstly noticed it didnt come in an anti-static bag and was bare in the slightly crushed box. I’ve plugged it in today and...
View ArticleSoftware uninstallation
@briannakata wrote: I need to uninstall the software/config changes installed by the script for the OnOff SHIM. I’m not seeing a way to use that script to do this so am assuming it needs to be done...
View ArticlePantilthat light control
@skypickle wrote: So the pimoroni pan tilt hat has three headers on the bottom - 2 for the servos and one for an LED light strip. Instead of a light strip i want to use a small laser diode. The diode...
View Article