Blinkt! as rsync progress bar?
@stian wrote: Hi folks. Just received my Blinkt! in the mail a couple of days ago, and so far I have been having fun delving into the example scripts in nano and seeing what exactly they are doing....
View ArticleHyperpixel 4.0: hyperpixel4-init not working
@Guardian wrote: So I bought a Hyperpixel 4.0 touch display a while ago, but I have not succeeded yet in getting it up and running with Rpi Zero W. My problem is: My Rpi Zero W works perfectly fine...
View ArticleHyperPixel 4.0 non-touch protocols?
@michael412 wrote: I just purchased a HyperPixel 4.0 but the only software I can find is the downloadable Raspbian variety. I would prefer to use this while running Windows IoT. That means writing my...
View ArticleEnviro pHAT - Temperature WAY off
@Alexander wrote: Hi, just installed my first Enviro pHAT. Basically it seems to be working fine, I can get reading, turn Leds on/off etc. But I wanted to build WLAN thermometers with it. And the...
View ArticleExplorer Hat Pro and Raspberry PI - Motor control NOK
@NiVeSaCo wrote: Hi, We’re new to Raspberry Pi and Explorer Hat Pro. We looked pretty much everywhere on the net and couldn’t find any information on how to fix it. The problem : using the explorer...
View ArticlePiCade Hat Wiring diagram
@aktelmiele wrote: Hi All I have the old PiCade Hat. I got the kit from you and it has 10 buttons. I was trying to use 6 for the controller. 2 at the front for start and reboot. and then 2 for the...
View ArticleKeybow Lighting Problems
@MarkMcD wrote: I have made two attempts at making an SD card. When I started either one up the pattern only goes on keys 7410852 . All keys can output to my computer. I modified mylayout.lua to...
View ArticlePan&Tilt bad i2c connection?
@lastcaress wrote: So I’ve finally gotten around to trying my pan&tilt hat and it’s not recognized (with i2cdetect) with several of my raspberry pies (3 B+ and A+) unless I apply a very specific...
View ArticleKeybow sends "c" instead of RIGHT_ALT (and other glitches)
@ghalfacree wrote: I’m perfectly willing to assume that I’m doing something bone-headed, here, but I can’t figure what. The Keybow’s working fine, but my attempt at creating my own layout isn’t going...
View ArticleRaspberry Pi Zero + Unicorn Hat HD: Not working [SOLVED]
@jerseyschorr wrote: Hi all, Hope you can help. I’ve got a fresh Rasbian image with the Unicorn HD Hat connected to my Zero. None of the demos are working, I can’t get anything. The examples “run” but...
View ArticleUnicorn HD issues
@JimmyBlunt wrote: Hi I’m quite new with pimoron and just got my Unicorn HAT HD . I wan to run it on a raspberry p zero and there is already the [JustBoom] Amp Zero attached and working fine. I...
View ArticleA stupid question
@psavas wrote: I need to ask a stupid question ('cause I’m a complete novice when it comes to electronics): I’m using a Zero LiPo shim and on the product page, it talks about how the “EN pin can be...
View ArticleOnOff Shim working Config
@janek wrote: Hi, I have problem with OnOff Shim my /etc/cleanshutd.conf is: config for cleanshutd (commented out values are the defaults) daemon_active=1 trigger_pin=4 led_pin=off poweroff_pin=4...
View ArticleWhat am I missing? OnOff SHIM fail
@snafu wrote: I just setup a system with the OnOff SHIM. When I press and hold the button, the red LED lights and that’s all it does. The RPi never shuts down. What am I missing here? I’m using...
View ArticleSwapped hyperpixel4 axis on clean install of raspbian18-11-13
@mikekscholz wrote: ok so I just got a blank sd, did a clean flash of the newest raspbian image, did the updates, then cloned and installed the repo without touching a single other thing just to make...
View ArticleButton Shim and Inky navigation
@td4dotnet wrote: Greetings all I am very new to Python and I am still getting to grips with it - I am at a point where I have collected a whole load of phats and hats and I want to start combining...
View ArticleClik here to view.
New Picade buttons and joystick not being recognised
@neilhigham wrote: Hi, I’ve just got a new Picade and when I go into EmulationStation it is not recognising the buttons or joystick. I’ve read through another thread: PICADE - X Hat- Buttons +...
View ArticleOn / Off Shim won't turn off
@crashmeplease wrote: Hi, Are there any log messages I can look for to diagnose why my on/off shim won’t turn off? The button turns it on ok, and the led illuminates when it’s pressed, so I guess it’s...
View ArticleClik here to view.
Writing to Inkyphat
@Ealingcommoner wrote: Hi all, New to this site but have had great fun playing with the inkyphat since it arrived. Working on adapting some code to turn my phat into a bus departure board. Everything...
View ArticleOther Audio Devices Cannot Work After pHAT DAC Is Set Up
@xiewt86 wrote: Hi, I’m using the pHAT DAC on my raspberry pi zero as an audio output and it works very well. However, after I set up the pHAT DAC according to the instruction here, I found that I...
View Article