Enviro+ doesn't work after restart
@germinator64 wrote: I’ve built the air quality monitor according to these instructions: https://learn.pimoroni.com/tutorial/sandyj/enviro-plus-and-luftdaten-air-quality-station It works quite well,...
View ArticleEnviro+ bme280 Library import in Weather.py
@DavidL wrote: I have just received an Enviro+ and following the “Getting started” instructions. I am using a Pi Zero running Raspbian Jessie. When I try to run the weather.py example I get the...
View ArticlePimoroni Trackball PIM447 issues: won’t work as mouse
@olifiers wrote: Hi there! Got a neat Pimoroni trackball, but having trouble with some of the github code supporting it. I can get some of the py examples to work (rainbow, colour-control) just fine,...
View ArticleFan SHIM isn't making good contact with GPIO pins
@jcx200 wrote: As the title says, I am not getting verry good contact on the fan shim PCB against the GPIO pins. The fan itself works but because the contact isn’t good enough, the LED on the shim PCB...
View ArticleRPi 4 fan shim
@otalado wrote: I just got the fan shim. I put it together, mounted it on my RPi 4 and installed the software for it. It seemed to work OK. During installation I set threshold to 65 degrees and...
View ArticleCO2 meter (NDIR) with Enviro+
@maxt wrote: Hi I would really need to connect a low cost NDIR CO2 meter together with the new Enviro+ and the PMS5003 particle meter and wonder if you have any ideas how to do this? The sensors I am...
View ArticleClik here to view.
No Module error
@manjulapra wrote: A noob here, both to Pi and HATs. I soldered a GPIO Header and connected the Enviro+ and did stuff according to here. But when I run any example I get the error “Module xxxx not...
View ArticlePi Zero WH Enviro+ 10mm standoffs too long?
@peterG wrote: The Enviro+ is an amazing phat and I got it all up and running in 10 minutes, so well done with the design! I bought a pair of black headers 10mm/2.5 to support the phat, but when I...
View ArticleEnviro+ do I need a filter for PMS5003 Particulate Matter Sensor
@peterG wrote: I’m testing out the PMS5003 Particulate Matter Sensor indoors at the moment but will eventually move the whole rig outdoors. I plan to design a “hat” for it and rig up a longish tube to...
View ArticleBlinkt Software
@MrDitchy wrote: Hi, I have correctly attached a blinkt! to my RPi 3B+. Following the link from the product page via GitHub I tried the command “sudo apt-get install pimoroni” . This gave me the...
View ArticleBreakout Garden SPI not working (0.96" screen)
@DM1985 wrote: Hi guys, A noobie. The SPI sockets on my breakout garden don’t seem to work with the 0.96" LED. I have SPI and IC2 set to ON one under Raspi config. The breakout garden code only...
View ArticleClik here to view.
Pantilthat Set-up Grief
@Rmb wrote: Hi, Just purchased a PanTiltHat from you and trying to set it up with a new RasPi 3 B+ following the how-to instructions on your website. Started with the recommended curl … | bash command...
View ArticlePiano and Drum HATs don't work properly on Pi 4 - Pi 4 at fault?
@arianne wrote: Hey everyone I’ve been getting my new Pi 4 set up so I can start tinkering with a few ideas for my local Code Club. I’ve only just got around to unwrapping and trying the Piano and...
View ArticleHyperpixel 4.0 Screen not working - service fails
@Bman1296 wrote: Hi All, First post, just received my Hyperpixel screen. I am trying to attach this to a RPi4, however after sudo apt-get upgrading and updating from a fresh install, I run the...
View ArticleRaspberry Pi 4 HDMI issues
@PiguyAnge wrote: Is anyone else not getting a consistent HDMI signal? I have the 4gb version. With hdmi safe mode I do get a display now but it is not consistent in reboot on working. And I get...
View ArticleClik here to view.
Picade screen won't power up
@justinpealing wrote: Yesterday I assembled my new Picade - everything was working great, but today I’m having problems powering on the screen. At first the screen came on, but wouldn’t stay on - it...
View ArticleHaving some issues with the UnicornHat
@DavidCordes wrote: When I import the unicornhat module, I receive the following error message: Traceback (most recent call last): File “/home/pi/test.py”, line 2, in import unicornhat as uh File...
View ArticleKeybow mini hangs?
@xTr wrote: Hi there… i’ve got a keybow mini (3 keys) and works great but… at some random times… HANGS… STOPS… At the beginning it wasnt even lit (i only used led colors on click), so, sometimes, not...
View ArticleHyperpixel 4 i2c header change
@Shoe wrote: Hello! I’ve been mulling over a project with the Hyperpixel 4 (non-square) which would involve adding additional inputs to the Pi. I was consideringr doing this via i2c using the header...
View ArticleAdafruit Feather M4 Express and Adalogger RTC
@richmars wrote: Hi, Just got a Feather M4 Express and Adalogger Featherwing RTC and SD. The SD card works with the card info program from the Adafruit website but the RTC doesn’t seem to work. Again,...
View Article