Pimoroni DAC and RCA
@Geniuscube wrote: Quick question, and probably a stupid one. I notice two big L and R holes on the DAC. Can I solder RCA connections on to these? Posts: 2 Participants: 2 Read full topic
View ArticleAdafruit Flora - LCD Display
@mfrench71 wrote: Hi I recently puchased an Adafruit Flora from you and would like to know if there is an LCD display that can be used with it. I'm looking to display just a few digits as an...
View ArticleRaspberry Pi Zero USB not receiving data
@oswaldizer wrote: Hello. I used my RPi Zero for quite some projects and it workde fin. Until one day it stopped working and just got very hot when plugged in..(very hot i almost burned my finger and...
View ArticleRaspberry pi 3 picade kit Undervoltage
@Perafkraftenyyy wrote: Have a 5V 2.4 a micro-USB charger and it doesn't seem to give the picade enough juice. Undervoltage symbol is constant on the 8" screen. What have I possibly done wrong? Posts:...
View ArticleSpeaker Bonnet - Adding volume control?
@Hiroshi wrote: tl;dr: Can I wire in a pot to act as a volume control? I love my Pi Zeros, especially the one I've set up with RetroPie, but it's a pain to get audio from directly (cheap monitor has...
View ArticleClik here to view.
pHAT DAC Output Components
@JasonW wrote: Hi, I'm intending to use the pHAT DAC with a RPi as a demonstartor for a system that will use the same DAC (PCM51xx). Would it be possible for you to divulge the components hanging on...
View ArticleChanging volume output
@PiNoob wrote: I installed a pHat Dac but now I need to use the GPIO pins for another project which needs a volume output, what do I do to change the volume output?Thanks for the help Posts: 5...
View ArticlePicade, retropie 2 player setup
@tiopepet wrote: Hello, first of all, excuse me, because my English is very bad, I need help. I have the picade machine connected to rapberry 2 and I want to play with two players, the emulator is...
View ArticleWhat do x, y, z values of Enviro pHAT accelerometer measure?
@jbrisbin wrote: I'm starting to play with a new Enviro pHAT on a RBP 3 and I can't find references in the documentation that describe what the x, y, and z values coming back from the accelerometer...
View ArticleProblem installing Unicorn Hat
@irowlands wrote: We are completely new to our raspberry Pi and are have a problem getting the Unicorn Hat software to install properly. Below is a copy of the error messages: pi@raspberrypi:/ $ curl...
View ArticleFlorence will not load
@russell wrote: Greetings! I have a problem loading Florence with error messages 1025 and 1026.Please see below for full details.Thanks in advance for your help and assistance in this matter. Florence...
View ArticleShare one Blinkt! with multiple RPi3
@MoCo wrote: Hello everyone, for a project, I need to display state leds of a RPi3 cluster. I was wondering if I could use Blinkt! board, since I like it very much. I'd like to use only one Blinkt!...
View ArticleWhy my order canceled?
@raonhaje wrote: I ordered Raspberry pi zero and some parts yesterday.PI159416But status is canceled.Why cancel my order? Posts: 3 Participants: 2 Read full topic
View ArticleNewbie with an Automation PHAT ADC question
@hbanzon wrote: Hi All -So I just got my Automation Phat. I'm going to use it to control my swimming pool heater, using the relay to switch the heater on/off. I was going to use a DS18B20 as the...
View ArticleEnviroPhat-Magnetometer
@amandeep wrote: Hi! I'd like to know how obtain data from the Magnetometer alone, and log this alongside the rest of the data as specified in the guide. Thanks! Posts: 1 Participants: 1 Read full topic
View ArticleDisplayotron hat not working
@johnw wrote: Hi guys. I have a project I am using a displayotron 3000 for but recently discovered it was replaced by the displayotron hat. I have ordered the newer display and tried using it but...
View ArticleProblems with Blue screen - Picade and retropi installation
@knightster98 wrote: Hi, I bought a Picade, last week and a complete PI 3 kit with 2.5A PSU, pre-installed SD card with Rasbian. After building the Picade - all OK, I fired up the PI 3 with the...
View ArticleDoes the Pi Zero Camera Module fit in Camera Mount?
@veryalien wrote: I'm just wondering, does the new Raspberry Pi Zero Camera Module (CAM003) fit in your standard Raspberry Pi Camera Mount (PIM012)?From the photos it looks like the camera itself...
View ArticleCan the Automation Phat put power through to the pi 0?
@Benhackerman wrote: I am going to use the raspberry pi 0 with the automation phat, can i put a 12v battery through the automation phat and also have it power the pi 0? Posts: 4 Participants: 2 Read...
View ArticlePanTiltHat & Picamera in python
@calleblyh wrote: Hi, I am not a programmer basically. But having ideas on my specific applications: I have the pantilthat which I can control to certain positions. I have the Picamera as well, and I...
View Article