Vl53l1x python3 support
@rbnman wrote: I’VE MOVED THIS TO THE DISCORD SITE Hi there. Just acquired the vl53l1x module from you and it works fine under python 2.7. using pip to install smbus2 and vl53l1x libraries. Is it...
View ArticleRobohat problem
@lufbrarunner wrote: Just got the robohat today, pretty pleased with it although I do get an error when I run some of the sample programs ‘servod: Cannot parse the hardware name string’ Anyone have...
View ArticleVl53l1x pip problem
@Richard42 wrote: Following the instructions I get … pi@Test-pi:~ $ sudo pip install vl53l1x Collecting vl53l1x Could not find a version that satisfies the requirement vl53l1x (from versions: ) No...
View ArticleAutomation HAT and sinking outputs
@McDiver wrote: Hi folks I’m using the excellent Autmation Hat for my big project. Now i’m going to use the sinking outputs to control som lights. But how many A/mah can i run to the internal ground...
View ArticleRaspberry Pi 3 B+ and Picade Hat
@takasaki wrote: Hi, I have a Raspberry Pi 3 B+ and the Picade Hat (the one with the joystick design). The Picade Hat doesn’t seem to power my Pi though the GPIO pins when I plug my power supply into...
View ArticleNew Picade screen controls
@ipguru wrote: The osd brightness controls on my new picade seem to make no difference to the dispaly brightness is there anything in particular I should be checking Posts: 1 Participants: 1 Read full...
View ArticleBME680 to Web service
@Noob wrote: I bought a BME680 sensor and got it working on the command line. What I’m wondering is how do I hook it up to a web service where I can conveniently see the readings? I can’t find any...
View ArticleClik here to view.
Raspberry Pi Zero with LiPo
@Distortion wrote: Hello, I want to make my Raspberry Pi Zero portable and i have a 3.7V LiPo laying around. Can I use this for the Pi Zero? shop.pimoroni.de PowerBoost 500 Charger - Rechargeable 5V...
View ArticlePicade buttons and screen problems
@Dvztb wrote: Hi there. So I got two picades in the pre order stage. I have built one. The screen ribbon has to be secured via tape or I can’t get a picture. I am having issues with the buttons. Have...
View ArticlePirate Radio project - PhatBeat buttons not working
@sallonoroff wrote: Hello all, I set up my Pi Zero Pirate Radio kit some months ago as an AirPlay speaker and all was well, except I found that the buttons on the PhatBEAT hat didn’t work. I’ve...
View ArticlePhat touch - Button B less responsibe
@djrara wrote: I tried my new phat touch for the first time. I ran the buttons.py to check the functions. All LEDs an buttons work, but button B is less responsive, compared to the other buttons....
View ArticleControl pihole with touchphat - how?
@djrara wrote: On my raspberry zero w, I want to control pihole with touchphat. When the button back is pressed, pihole should disable blocking for 10 mins, when enter is pressed, pihole should enable...
View ArticleSpeaker phat not working (again?)
@veryalien wrote: After struggling to get my speaker phat working a few months ago it’s now either died, or something’s changed in the software/distribution. It’s the ‘usual’ problem of no sound but...
View ArticleThe IR Camera
@Bonzadog1 wrote: I think the pimoroni pan/tilt cannot handle the IP Camera. Can someone recommend me one , All the best Posts: 2 Participants: 2 Read full topic
View ArticleSpeaker Phat + Retropie Voume
@cyclonus wrote: Hi Guys Just a question about the speaker phat and retropie, I currently have this all connected up and the sound is coming out but even on 100% PCM it is very low. I know this...
View ArticleRetropie not switching to hdmi
@thepibaker04 wrote: So I have just bought the Hyperpixel 4 and I wanted to use it for retropie, so I lookt up how to make it switch from the Hyperpixel to an HDMI monitor and found dozens upon dozens...
View ArticleHyperPixel Screen Protector
@major_tomm wrote: Just bought a shiny new HyperPixel 4 and I’m yet to take the protective plastic off. Is this the sort of screen that might benefit from a screen protector if it’s handled a lot? I’m...
View ArticleClik here to view.
Bluish Hyperpixel 4
@Curve wrote: I got my new Hyperpixel 4 late last week and set it up using the instructions/installer on your website. Everything looked great but then the image turned to a blue tint. I tried...
View ArticleWeird Problems with Picade Joystick
@Cullmeister wrote: Hi, Got My picade and was able to get it going. However I’m having issues with the joystick. Only the directions up, up left, up right and right work. After looking around here I...
View ArticleDisplay-o-tron hat backlight is flickering
@collene wrote: I haven’t used my display-o-tron hat for awhile, but I wanted to use it with an enviro-phat I just picked up. It displays fine, but when I run the demo program, the backlight...
View Article